EXFO Photonic Solutions Div. IQS-12001B User Manual download pdf (Page 7)

IQS-12001B

Cable Assembly and Component Test System

www.EXFO.com

SPECIFICATIONS

FTB-85102 FTB-8510-12 FTB-8510-2

Ports Gigabit Ethernet Two 10/100Base-T Two 10/100Base-T Two 10/100Base-T and two

and one Gigabit Ethernet

Connector types RJ-45 (ISO 8877) RJ-45 (ISO 8877) and LC RJ-45 (ISO 8877) and LC

Connect speed (Mb/s) 10/100 10/100/1000 10/100/1000

Duplex mode Full/half-duplex Full/half-duplex Full/half-duplex

auto-negotiation auto-negotiation auto-negotiation

Maximum port capacity (Mb/s) 200 (bidirectional) 2000 (bidirectional) 2000 (bidirectional)

Ethernet testing RFC 2544 RFC 2544 RFC 2544

RFC 1242 RFC 1242 RFC 1242

SPECIFICATIONS

Singlemode

(1310/1550 nm) Singlemode

(1490/1625 nm) Multimode

Testing time

(s) < 6 < 6 < 6

Cable assembly length (m) 1.8 to 1500 1.8 to 1500 1.8 to 500

Insertion loss measurement uncertainty ± 0.03

± 0.03

± 0.07

Insertion loss measurement stability

(dB) < 0.005 < 0.005 < 0.028

Reflectance range (dB) −30 to −75 −30 to −75 −10 to −50

Reflectance measurement uncertainty (dB) ±1 (−30 to −70) ±1 (−30 to −70) ± 1.2 (−10 to –30)

± 1.5 (−30 to –40)

±2.2/±1.7 (−70 to −75) ±1.7 (−70 to −75) ± 1.6 (−40 to –43)

± 2.9 (−43 to –50)

Reflectance measurement repeatability

(dB) ±0.1 (−30 to −65) ±0.1 (−30 to −65) ± 0.2 (−10 to –30)

±0.2 (−65 to −70) ±0.2 (−65 to −70) ± 0.4 (−30 to –40)

±0.4 (−70 to −75) ±0.5 (−70 to −75) ± 0.6 (−40 to –43)

± 1.8 (−43 to –50)

Wavelengths (nm) 1310/1550 1490/1625 850/1300

Output channels Up to 32 channels Up to 32 channels Up to 32 channels

Test method End-to-end/bidirectional End-to-end/bidirectional End-to-end/bidirectional

Notes

a. Calculated and measured with the following considerations:

• Based on recommended procedure for ORL measurements

• The FOA-300 series’ uncertainty is included in all uncertainty values

• Although tests are possible with other fiber-optic adapters, these specifications are only valid with the FOA-300 series

• Cable assemblies < 1.8 m can be tested using a non-reflective termination

• With 15 minute warm-up time

b. For SMF-28 fiber. At 23 ºC ± 1 ºC in High-Sensitivity Reflectance mode with no switch.

c. At 850 nm and 1300 nm. For 62.5/125 µm fibers. At 23 °C ± 1 °C, after 30 minutes warmup. Switch module connectorized with FC/PC connectors.

Uncertainty due to launching conditions not included.

d. Calculation and storage time for simplex, dual-wavelength IL/reflectance end-to-end measurements (Standard Reflectance Sensitivity mode, 500 meter range);

does not include referencing and connection time.

e. For simplex measurements using FOA-322 adapter. Uncertainty for MTP to MTP, MT-RJ to MT-RJ, MTP to fanout and MT-RJ to fanout is ± 0.06 dB

(reported with a level of confidence of 95 %). This does not include uncertainties due to connector, connector adapter or switch PDL.

f. For simplex measurement using FOA-322 adapter. Uncertainty for MTP to MTP, MT-RJ to MT-RJ, MTP to fanout and MT-RJ to fanout is ± 0.08 dB

(calculated for a level of confidence of 95 %). Does not include uncertainties due to connector, connector adapter or uncertainties due to mode dependence of the switch.

g. For a stable connection, over 15 minutes, at constant temperature.

h. For a stable connection, over 10 measurements.

GENERAL SPECIFICATIONS

Communication interfaces

General-purpose interface bus (GPIB)

Ethernet (10/100 Base-T)

RS-232

Temperature

Operating 0 °C to 40 °C (32 °F to 104 °F)

Storage −40 °C to 60 °C (−40 °F to 140 °F)

Relative humidity 80 % maximum, non-condensing

Laser Safety

21 CFR 1040.10 CLASS 1 LASER PRODUCT

IEC 60825-1:2001 CLASS 1 LASER PRODUCT

Standard Accessories

Expansion units as required, user guide, certificate of compliance, custom report, label generator, IQS-12001B software and EUI-89 FC narrow key connector.